Standard Parts

           فهرست تصویری قطعات پیش ساخته

 

 

  • Locset Anaerobic Adhesive -Retaining or Joining

    ● LOCSET Retaining or Joining
    LOCSET Retaining or Joining for installing cylindrical (coaxial) parts, gears, sprockets, bushings, bearings and... Used in housing or on the shaft and with excellent strength, they even cause even permanent connection. Adhesives of this group are the best alternative for pressing Tolerances and even precision Tolerances and is also suitable for parts that are loose in place.

    ...
  • Precision Punch D225

    ● DIN 9861
    ● Material :WS , HWS , HSS

  • Sliding Pad D067

    ● Non-Liquid Lubricant
    ● Material: Bronze/Cast Iron
    ● ISO 9183-1
    ● Are used in applications of linear or rotary motion in tool making, and similar engineering uses.
    ● Advantages of oilless guide elements:
    - Good emergency sliding properties.
    - Highest carrying capacity at low speed.
    - Useable under water or with chemical solutions.
    - Extremely wide temperature resistance hot and cold.
    - Damping properties in presence of vibration.

  • Rectangular Die Set CR

    ● Cast Iron-Rear Pillars
    ● DIN 9822
    * Different from DIN 9822

    ...
  • Matrix Without Collar D267

    ● Material : HSS
    ● ISO 8977
    ● Description:
    - Possibility of producing all sizes and shapes.d1 hole has been created for wire-cut pass.

  • Guide Pillar (Angle Pin) D01

    ● Material : ~ 1.7131 | 720HV

    ...
  • All-Steel Die Set 2SH

    ● With Stripper - Plates Material: St37, St52, 1.1730
    ● Similar DIN 9868/ISO 11415

    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 . in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.

    ...
  • All-Steel Die Set 2SM

    ● With Stripper - Plates Material: St37, St52, 1.1730
    ● Similar DIN 9868/ISO 11415

    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 . in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.

  • All-Steel Die Set 2SR

    ● With Stripper - Plates Material: St37, St52, 1.1730
    ● Similar DIN 9868/ISO 11415

    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 . in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.

  • All-Steel Die Set 2SZ

    ● With Stripper - Plates Material: St37, St52, 1.1730
    ● Similar DIN 9868/ISO 11415

    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 . in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.

  • PULL-DOWN CLAMP E3067

    ● Extra Strong Clamping Jaws
    ● Material: Cast Iron ,Heat-Treated Steel

    ...
  • FORKED CLAMP WITH PIN END E308

    ● Material : Heat-Treated Steel
    ● DIN 6315C

  • Date Marked Pins

    ● Special For Die - Casting

  • Manifold Block H52401

    ● Material: 1.2312
    ● Features and Benefits:
    1 ) The symmetrical design with the equal length run of injection from the main runner to each of the cavity, even in linear arrangement or with a high cavity number.
    2 ) Optimal placement on the input and output of thermal elements to allow them to securely insert them.
    3 ) Uniform heat distribution in the Manifold block, measurement and temperature control in the depth of block.
    4 ) Applying new and optimal methods for blocking and changing the material path with high reliability.
    5 ) Close interaction of SETAAK with the customer to reach the best design.

  • Oilless Guide Bush D046

    ● Non-Liquid Lubricant
    ● Material: Bronze
    ● DIN 9834/ISO 9448
    ● Are used in applications of linear or rotary motion in tool making, and similar engineering uses.
    ● Advantages of oilless guide elements:
    - Good emergency sliding properties.
    - Highest carrying capacity at low speed.
    - Useable under water or with chemical solutions.
    - Extremely wide temperature resistance hot and cold.
    - Damping properties in presence of vibration.

  • Ejector Pin-Cylindrical Head D411K

    ● DIN 1530 - Shape C/ISO 8694
    ● Material: WAS(Hot Working Steel Nitrided)
    ● Plasma - Nitrided Black Oxidized

  • Locset Liquid Adhesives -UV

    LOCSET U.V adhesive are one component and solvent free.
    They are used for bonding parts made of glass , ceramics , synthetic mterials ( plasics ) and matrials that need ineffective ( transparts ) or sired production and assembly ( fast hardening )

    ● Advantages:
    1-one-component
    2-easy to handle
    3-fast cure
    4-cure at room temperature
    5-low conectration of pollutant substances at workspace
    6-low temperature development during curing
    ● liquid UV
    The Liquid UV adhesives based on acrylate for bonding of glass , translucent synthetic materials among each other or with metals , ceramics and non-translucent synthetic materials.
    The adhesivs are one-component, They cure at room temperature visible light

  • Plate SP

    ● Material: St 37 , St 52 , 1.1730
    ● Special machining of plates can be done on request.

  • Guide Pillar (Angle Pin) 019

    ● Material : ~ 1.7131 | 720HV

  • Spring D62

    ● Din 2093

  • Blue Spring D64B

    ● DIN/ISO 10243

  • BLOCK STOPPER E3068

    ● Material: Cast Iron

    ...
  • PRECISION SUPPORTS E313

    ● Material: Heat-Treated Steel

    ...
  • COLLAR NUT E401

    ● Material: Forged, Turned, Heat-Treated Steel
    ● DIN 6331
    ● Height 1.5 dia.
    ● Tensile strength class 10.
    * Different from DIN 6331

    ...
  • Oilless Guide Bush D043

    ● Non-Liquid Lubricant
    ● Material: Bronze
    ● Are used in applications of linear or rotary motion in tool making, and similar engineering uses.
    ● Advantages of oilless guide elements:
    - Good emergency sliding properties.
    - Highest carrying capacity at low speed.
    - Useable under water or with chemical solutions.
    - Extremely wide temperature resistance hot and cold.
    - Damping properties in presence of vibration.